Recent Posts

Topics with their latest replies in reversed order
	G120 runs the pump backwards after a motor swap By mtl514 2 weeks ago \| Last Post: 2 weeks ago Forum Drives & Electrical
	A bolted guard is why nobody checks rotation. Ours... 2 weeks ago By edj Got the guard off first thing with a second pair o... 2 weeks ago By mtl51... The drive does not know which way the motor turns.... 2 weeks ago By gunth... view all posts
	20 HP DOL motor hums and won't turn, overload trips after a minute By rookie_ray 2 weeks ago \| Last Post: 2 weeks ago Forum Drives & Electrical
	Clip was heating the fuse for months. Then one hot... 2 weeks ago By edj C fuse open. The lugs on the disconnect were fine ... 2 weeks ago By rooki... That's single phasing. C is open somewhere upstrea... 2 weeks ago By vinni... view all posts
	S7-1500 OPC UA connection refused from the office subnet, works from the plant By northbay 2 weeks ago \| Last Post: 2 weeks ago Forum Networks & Comms
	Same trap here, a 102 rule from an old ticket nobo... 2 weeks ago By mira8... IT added TCP 4840, office host to the CPU, one lin... 2 weeks ago By north... OPC UA is its own port, 4840 by default, and a rul... 2 weeks ago By pnina view all posts
	1756-EN2T webpage media counters, what do FCS errors mean when a rack shows 16#0204 By rookie_ray 2 weeks ago \| Last Post: 2 weeks ago Forum Networks & Comms
	hand crimps. every plant has one and its always in... 2 weeks ago By ramon... Factory lead in, EN2T to the switch. Reset the cou... 2 weeks ago By rooki... That plug is your problem. A short strand in a han... 2 weeks ago By pat_k view all posts
	KTP700 Basic shows By annaz 2 weeks ago \| Last Post: 2 weeks ago Forum HMI & SCADA
	Normal, sadly. The HMI compiler doesn't check PLC ... 2 weeks ago By kiran... Fixed. First I unticked optimized to watch the val... 2 weeks ago By annaz I'd go with the second as well. The tutorial wasn'... 2 weeks ago By tomhw view all posts
	Motor current into a CompactLogix via CTs for predictive maintenance, is it worth it By carlh 2 weeks ago \| Last Post: 2 weeks ago Forum Drives & Electrical
	Unbalance shows up as heat. Put the IR gun on thos... 2 weeks ago By danr4... Four CTs on the four motors that matter, the infee... 2 weeks ago By carlh 1 s scan, 30 s average into the historian, and one... 2 weeks ago By scott... view all posts
	1756-EN2T off the network after IT enabled port security, switch port err-disabled By mtl514 2 weeks ago \| Last Post: 2 weeks ago Forum Networks & Comms
	Moved to Networks & Comms. Marking solved. 2 weeks ago By plctr... IT removed the stale sticky line, put my EN2T's MA... 2 weeks ago By mtl51... The shut and no shut clears the violation, not the... 2 weeks ago By north... view all posts
	EtherNet/IP I/O drops 16#0204 about five minutes after every switch reboot By ines31 2 weeks ago \| Last Post: 2 weeks ago Forum Networks & Comms
	Get the querier line into their standard config wh... 2 weeks ago By petek Two shifts, nothing dropped, so I'm closing it. IG... 2 weeks ago By ines3... Watch the 525s. They're first to drop when a group... 2 weeks ago By north... view all posts
	ControlLogix T04:C34 timer preset negative after operator loads a recipe By ramonv 2 weeks ago \| Last Post: 2 weeks ago Forum Rockwell / Studio 5000
	Learned that one the same way, on a filler. Not fu... 2 weeks ago By rsdav... Done both. Offset back to 0 on the panel tag, min ... 2 weeks ago By ramon... There it is, and it's not just one fix. Both sides... 2 weeks ago By hanna... view all posts
	Line-fed screw conveyor motor burned out, panel builder skipped the overload By rookie_ray 2 weeks ago \| Last Post: 2 weeks ago Forum Drives & Electrical
	Open the third one before it teaches you the same ... 2 weeks ago By ronh5... Fitted an overload under the contactor, dial at 4.... 2 weeks ago By rooki... What ron said. Every line-fed motor gets its own o... 2 weeks ago By boris... view all posts

Page 11 / 23 Prev Next